網站公告:

新聞中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.9015c.com

常見問題

當前位置:首頁 - 新聞中心 - 常見問題 - 關于氣液增壓泵的正確打開

關于氣液增壓泵的正確打開認識方式

發布時間:2022-06-22 18:00:14   發布人:http://www.9015c.com
當驅動部分和輸出液體部分之間的壓力達到平衡時,氣液增壓泵會停止運行,不再消耗空氣。當輸出壓力下降或空氣驅動壓力增加時,增壓泵會自動啟動運行,直到再次達到壓力平衡后自動停止。此外大家還需知道的該增壓泵更多相關內容。
When the pressure between the driving part and the output liquid part reaches equilibrium, the gas-liquid booster pump will stop running and no longer consume air. When the output pressure drops or the air drive pressure increases, the booster pump will automatically start and run until it reaches the pressure balance again. In addition, you need to know more about the booster pump.
氣液增壓泵特點
Characteristics of gas-liquid booster pump
1、維護簡單:增壓泵零件和密封件少,維護簡單,成本低。
1. Simple maintenance: the booster pump has few parts and seals, simple maintenance and low cost.
2、性價比高:增壓泵具有輸出性能高、成本低的特點。
2. High cost performance: booster pump has the characteristics of high output performance and low cost.
3、可調性強:增壓泵的輸出壓力和流量由驅動氣體的調壓閥調節。調整驅動氣壓,使氣壓管路增壓泵的輸出壓力在預增壓氣壓和大輸出壓力之間調整。
3. Strong adjustability: the output pressure and flow of booster pump are regulated by the pressure regulating valve of driving gas. Adjust the driving air pressure so that the output pressure of the booster pump of the air pressure pipeline is adjusted between the pre pressurized air pressure and the large output pressure.
4、輸出壓力高:可實現氣動液體管道增壓泵的高工作壓力,可實現氣動氣體管道增壓泵的高工作壓力。
4. High output pressure: it can realize high working pressure of pneumatic liquid pipeline booster pump and high working pressure of pneumatic gas pipeline booster pump.
5、材質優良:增壓泵高壓部分采用硬質鋁合金制造。高壓柱塞由不銹鋼制成。并采用雙層密封。關鍵部位的材料可根據介質進行選擇。
5. Excellent material: the high-pressure part of booster pump is made of hard aluminum alloy. The high pressure plunger is made of stainless steel. And adopt double-layer sealing. The materials of key parts can be selected according to the medium.
氣液增壓泵
氣液增壓泵的使用方法:
Usage of gas-liquid booster pump:
1、用戶應準備好加壓氣體及管道、驅動氣體及管道、高壓氣體的出口管道。先按照增壓泵出廠時的說明書固定增壓泵。檢查進出口接頭尺寸,連接管路,檢查耐壓是否足夠,接頭是否漏水等,檢查無誤后,即可進行增壓試驗。
1. The user shall prepare pressurized gas and pipeline, driving gas and pipeline, and outlet pipeline of high-pressure gas. First, fix the booster pump according to the factory instructions of the booster pump. Check the size of inlet and outlet joints, connecting pipelines, whether the pressure resistance is sufficient, whether the joints leak, etc. after the inspection is correct, the pressurization test can be carried out.
2、氣源:氣液增壓泵的驅動氣源一般在1.8-8bar的壓力范圍內。不建議其驅動氣源超過10bar。如果驅動氣源過高,會對泵體產生很大影響。造成損害,甚至給操作者造成更多的傷亡
2. Air source: the driving air source of the gas-liquid booster pump is generally within the pressure range of 1.8-8bar. It is not recommended that the driving air source exceed 10bar. If the driving air source is too high, it will have a great impact on the pump body. Cause damage and even more casualties to operators
3、在氣液增壓泵選型方面:客戶應根據自己的壓力,根據自己的壓力要求,選擇相應的增壓比,關注氣源壓力、進氣壓力、輸出壓力需求、流量、銷量工程師可以幫助您更準確地選擇
3. In terms of selection of gas-liquid booster pump: customers should select the corresponding boost ratio according to their own pressure and pressure requirements, focusing on air source pressure, inlet pressure, output pressure demand, flow and sales volume. Engineers can help you select more accurately
4、現場使用環境:現場使用環境必須清潔,無過多灰塵顆粒,驅動氣源和加壓介質中不應含有過多水分,會大大降低使用壽命。
4. Site service environment: the site service environment must be clean and free of excessive dust particles. The driving air source and pressurized medium should not contain too much moisture, which will greatly reduce the service life.
5、管道要求:客戶在現場使用時必須檢查高壓輸出管道的密封性。使用的管路、閥門和壓力表必須大于氣液增壓泵輸出的額定壓力。
5. Pipeline requirements: the customer must check the tightness of the high-pressure output pipeline when using it on site. The pipeline, valve and pressure gauge used must be greater than the rated output pressure of the gas-liquid booster pump.
6、對壓力容器的要求:所有承壓部件,特別是壓力容器,必須有壓力安全容器生產企業出具的壓力安全容器檢驗報告。
6. Requirements for pressure vessels: all pressure containing parts, especially pressure vessels, must have pressure safety vessel inspection reports issued by pressure safety vessel manufacturers.
以上就是今天為大家分享的關于問題的相關內容,希望對大家能有所幫助,想要了解更多內容可以電話聯系我們或者關注我們的網站http://www.9015c.com
The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.9015c.com 。
新聞推薦:
增壓泵在沒有水的情況下不停止工作原因 2022-07-18
增壓泵使用長久后會出現故障的表現形式 2022-07-11
訂購到滿意的增壓泵就要知道參數及其他 2022-07-04
關于氣液增壓泵的正確打開認識方式 2022-06-22
增壓泵怎樣安裝?有什么安裝常見問題? 2022-06-15
講解增壓泵產品九大特點 2022-06-08
氣體增壓泵要加一個氣罐的原因 2022-05-30
選擇氣體泄漏檢測儀時要了解實際情況 2022-05-27
氣體增壓泵和氣液增壓泵兩種設備可不能... 2022-05-23
氣體增壓系統典型應用的相關內容 2022-05-18

13188935873

qq

熟女av,各种作爱视频,国产乱子伦一级A片观看,第九色