網站公告:

新聞中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.9015c.com

常見問題

當前位置:首頁 - 新聞中心 - 常見問題 - 增壓泵在沒有水的情況下不

增壓泵在沒有水的情況下不停止工作原因

發布時間:2022-07-18 19:32:00   發布人:http://www.9015c.com
如果您發現增壓泵在沒有水的情況下不停止工作,可能是以下原因造成的:
If you find that the booster pump does not stop working without water, it may be caused by the following reasons:
1、可能是停機壓力值設置過高。如果停機壓力設置過高,無論有無水,增壓泵都無法達到設定壓力,自然不停機。
1. The shutdown pressure may be set too high. If the shutdown pressure is set too high, no matter there is no water, the booster pump cannot reach the set pressure and will not shut down naturally.
解決方法:如果有指針壓力表,先看電流不停止時指針壓力指示的位置,記下壓力值,然后檢查對應的設定停止壓力值(僅針對可以自己設置)。壓力值),適當降低設定的停機壓力值,然后重試。
Solution: if there is a pointer pressure gauge, first look at the position indicated by the pointer pressure when the current does not stop, write down the pressure value, and then check the corresponding set stop pressure value (only for self setting). Pressure value), reduce the set shutdown pressure value appropriately, and then try again.
氣液增壓泵
2、單向閥漏水。單向閥的作用是防止已經加壓的水的壓力倒流,造成壓力下降。如果單向閥密封不好導致漏水,則無法達到設定的上限,泵也不會停止。
2. The check valve leaks. The function of one-way valve is to prevent the pressure backflow of pressurized water, resulting in pressure drop. If the one-way valve is not well sealed, resulting in water leakage, the set upper limit cannot be reached, and the pump will not stop.
解決方法:先將增壓泵加壓到一定值,記下該值,然后關閉增壓泵電源,觀察指針是否會下降,如果下降則表示漏水。如果沒有壓力表,只能停一會,然后打開水龍頭,看看水壓有沒有明顯下降。
Solution: first pressurize the booster pump to a certain value, write down the value, then turn off the power supply of the booster pump, and observe whether the pointer will fall. If it falls, it means water leakage. If there is no pressure gauge, you can only stop for a while, and then turn on the tap to see if the water pressure drops significantly.
3、其他水管有漏水現象。管網其他水點漏水也會導致壓力持續下降,達不到設定的停機壓力值。
3. Other water pipes are leaking. Water leakage at other water points in the pipe network will also cause the pressure to continue to drop and fail to reach the set shutdown pressure value.
解決方法:這種可能性不大,但還是要觀察是否有泄漏。
Solution: This is unlikely, but it is still necessary to observe whether there is leakage.
4、增壓泵的控制器或傳感器壞了。如果經過以上3個步驟仍然無效,則可能是增壓泵的控制器或傳感器壞了。
4. The controller or sensor of the booster pump is broken. If the above three steps are still invalid, the controller or sensor of the booster pump may be broken.
解決方法:這種性比較強,一般不要在沒有廠家指導的情況下輕易測試,有觸電的危險。
Solution: this kind of specialty is relatively strong. Generally, it is not easy to test without the guidance of the manufacturer. There is a risk of electric shock.
另外,達到壓力平衡后,泵自動停機,采用單氣控不平衡配氣閥,實現泵的自動往復運動。泵體氣動部分采用鋁合金制造。與液體接觸的部件根據不同介質采用碳鋼或不銹鋼制造,泵的全套密封件均采用進口優質產品,從而保證了氣液增壓泵的性能。
In addition, when the pressure is balanced, the pump will stop automatically, and a single pneumatic unbalanced valve is used to realize the automatic reciprocating motion of the pump. The pneumatic part of the pump body is made of aluminum alloy. The parts in contact with liquid are made of carbon steel or stainless steel according to different media, and the full set of seals of the pump are imported high-quality products, so as to ensure the performance of the gas-liquid booster pump.
增壓泵在沒有水的情況下不停止工作原因便是這樣了,如果您還有其他問題就來關注我們網站http://www.9015c.com吧!
The reason why the booster pump doesn't stop working without water is this. If you have other problems, please follow our website http://www.9015c.com Come on!
新聞推薦:
增壓泵在沒有水的情況下不停止工作原因 2022-07-18
增壓泵使用長久后會出現故障的表現形式 2022-07-11
訂購到滿意的增壓泵就要知道參數及其他 2022-07-04
關于氣液增壓泵的正確打開認識方式 2022-06-22
增壓泵怎樣安裝?有什么安裝常見問題? 2022-06-15
講解增壓泵產品九大特點 2022-06-08
氣體增壓泵要加一個氣罐的原因 2022-05-30
選擇氣體泄漏檢測儀時要了解實際情況 2022-05-27
氣體增壓泵和氣液增壓泵兩種設備可不能... 2022-05-23
氣體增壓系統典型應用的相關內容 2022-05-18

13188935873

qq

熟女av,各种作爱视频,国产乱子伦一级A片观看,第九色